JACKYLED L Shape LED Strip Connectors for Living Room Accent Lighting and Bedroom Decor, 10mm 4-Pin RGB Corner Kit
JACKYLED L Shape LED Strip Connectors for Living Room Accent Lighting and Bedroom Decor, 10mm 4-Pin RGB Corner Kit
Couldn't load pickup availability
Why you'll love it
- Solderless snap design removes the need for a soldering iron, making it accessible to beginners
- Dual-purpose kit combines L-shape corner connectors and straight extension couplers in one purchase
- Orientation-agnostic design works regardless of which side the RGB+ pad is on, preventing install mistakes
- Compatible with the most common 10mm 4-pin SMD 3528/5050 strips including waterproof versions
- Bulk 20-pack with 2 bonus couplers and printed instructions reduces the need to re-order mid-project
- Water-resistant rating allows the same connectors to be used for both indoor and outdoor runs
- Works with Lepro LED strips when other brands like JACKEYLED did not
- Holds tight with little teeth that clamp down on contacts, better than other brands tried
- Relief of finding connectors that actually work after failures with competitor products
- Works flawlessly even with offset 3-pin 10mm strips (e.g., Monster brand) using 4-pin 10mm connectors
- Second-time purchase shows repeat satisfaction
- Easy to use even without prior experience with small electronic flexible circuits
- Having extra clips and connectors included made installation smoother
Perfect for
- Joining two LED strip runs around a 90-degree corner without cutting or soldering
- Extending an LED strip run along a straight line to reach farther distances
- Repairing a broken or disconnected section of an existing 10mm LED strip
- Completing a full-room RGB strip installation including corners and room wrap-arounds
- Connecting waterproof outdoor LED strips for patio or deck accent lighting
- Fixing accidentally cut LED strips
- Repairing torn Govee LED strips after project mistakes
- Creating a U-shape out of LED strips for a bookcase
- Cornering LED strips around TVs (especially with offset 3-pin Monster brand strips)
- Rescuing cut-off sections of TP-Link Tapo L900 LED strips for reconnection
- Cabinet LED installation
10MM 4-Pin Led Strip Connectors Kits - DIY Project Essential
Before purchase, please confirm that your led strip lights are 4-pin with 10mm width, if you are not sure , please contact JACKYLED Online Service with pictures or check with strip light supplier to get the width & pins
Two ways to connect
Why choose JACKYLED LED Connectors?
The connector set for RGB LED light strips comes with easy-clasp connector clips and 90 degrees L shape PCB boards. You can connect with light strips directly without any tools or welding operations. The unwired design ensures a gapless layout when you need to turn your LED strips around corners. Compatible with both ordinary and waterproof 4-pin light strips.
Package Includes:
10 pcs L shape RGB sheets --For corner connection
22 pcs 4-pin connector clips --For direct connection with led strips
10pcs L shape RGB sheets
Thoughtful and considerate to ensure the smooth progress of your DIY project
ONLY compitiable with 10 mm 4 Pin Strip Lights, Not 8mm, 2pin, 3 pin
22 pcs 4-pin connector clips
Cost-effectiveness price with enough quantity to clip with long LED strips
ONLY compitiable with 10 mm 4 Pin Strip Lights, Not 8mm, 2pin, 3 pin
Corner Connections
2 clips with 1 L shape sheet, perfect combination to connect with cornner area of wall, bed, shelf, gaming table etc
Extended Connections
2 clips to connect LED light strips directly, perfect to create charming atmosphere
Installation Instructions:
1.Open the clip on the side
2.Slid the 10mm 4pin LED light strip inside the clip underneath the contact prongs, if not 10mm 4 pin, it can't insert sucessfully
3.Make sure the side of the strip aligns with the "+ -" polarity, Then, close the wire clip
Product Information
Dual Purposes: This LED strip connector kit comes with detachable L sheets and straight couplers, perfect for both 90 degree corner connections and extensions along a straight line. Total 22pcs connector clips and 10pcs L Shape connectors For All 4 Pin Light Strips: Work with any 4-pin 10mm (0.39in) wide SMD 3528/5050 multicolor LED flexible strip lights, whether they are waterproof ones or non-waterproof lights for indoor use. Solderless Solution: Create a quick shunt, solid connection without the hassle of soldering. Just slide the light strip under the connector's pins and snap the clip. (Tip: Please do not pry up the metal pins. Doing so may cause poor contact.) Go Both Left and Right: No matter in what orders are the RGB+ marked on the connectors, the connection work as long as the + of the light strips on both sides are aligned. You Get Extra: Apart from 10 pieces of L boards and 20 connector clips in this 10-pack, 2 extra couplers are included, as well as detailed instructions both printed and online. If you need any help when using the connectors, please feel free to contact our online customer service team.
Features & Specs Indoor Outdoor Usage Indoor Additional Features Only work with 10mm 4pin led strip lights, Total 32 pcs Light Source Type LED Power Source Corded Electric Light Color RGB Voltage 12 Volts Wattage 72 watts Water Resistance Level Water Resistant Style Color White Theme Indoor Occasion Christmas Product Style simple Measurements Number of Light Sources 60 Item Weight 0.07 Pounds Number of Items 20
Frequently Asked Questions
Will these connectors keep my LED strip installation looking clean behind the TV and around room corners?
Yes. The L-shaped boards lay flat against the wall or cabinet edge, and the slight flex in the connector helps the strip sit flush at corners so the finished look reads as a continuous light line rather than a series of joints.
Can I use this kit to wrap RGB strips around an entire living room without obvious dark spots?
Absolutely. Combining the 10 L-shape corners with the 20 straight couplers lets you navigate door frames, bookcases, and ceiling transitions in one continuous run, which helps the color stay even from start to finish.
Does the connector stay hidden once the strip is mounted, or will it interrupt the room aesthetic?
The boards are designed to sit low and the strip lays on top, so once installed in a channel, behind a TV, or under a cabinet the connectors are essentially invisible from normal viewing distance.
Will the L-shape work for a U-shape layout around my bookcase accent lighting?
Yes, this is one of the most common projects for the kit. The L-shape corners handle the two 90-degree turns while the straight couplers cover the longer runs along the top and bottom of the bookcase.
Can I match these connectors with both warm white and multicolor RGB strips in the same room?
Yes. As long as the strips are 10mm wide 4-pin SMD 3528/5050, the same connector set will work for both color modes, so you can mix accent types without swapping hardware.
Is this kit enough to complete a full bedroom RGB makeover in one purchase?
For most bedrooms, the 32-piece kit (10 L-shape, 20 straight, 2 bonus) covers corners along the ceiling, behind the headboard, and any straight runs along closet or desk areas without needing to reorder mid-project.
Will the connectors affect the brightness or color of my RGB strip at the joint?
The clamp pins bite directly into the copper pads, so the electrical connection is solid and the color and brightness remain consistent across the joint when installed correctly.
Do these work for a kitchen under-cabinet project where aesthetics really matter?
Yes. Under-cabinet runs often need an L-shape at the corner, and these connectors are sized to disappear inside standard LED channels or sit neatly tucked under the cabinet lip.
Can I use this for a behind-the-TV entertainment center with corner framing?
That is one of the most popular uses. The L-shapes handle the 90-degree transitions at the TV frame, and the bidirectional design means you do not have to worry about which side the RGB+ pad lands on.
Will the corners look bulky on visible runs like ceiling coves or crown molding?
No, the connector profile is slim and the slight flex lets you press it flat into a cove. For most ceiling and crown applications the joint becomes invisible once the strip is lit.
Are these connectors better-looking than the DIY solder joints I made on my last project?
In most cases, yes. A clean solder joint is possible but requires skill, and any cold joint leaves a visible bump and dim spot. The snap-down design produces a flat, consistent joint with no solder blobs.
Can I leave the extra connectors in the kit for future room updates?
Yes, the bulk 32-piece count is intentional. Most buyers keep a few L-shapes and straight couplers in a drawer for the next time they rearrange furniture or extend a strip to a new accent area.
Will this work for an accent wall or floating shelf LED install?
Yes. Floating shelves and accent walls typically need a few short straight runs and one or two corners, which is well within the count of the 20-pack kit.
How do these compare to just buying a pre-wired corner LED strip from a decor brand?
Pre-wired corner strips lock you into one brand and one color temperature, while these connectors let you use whatever 10mm RGB strip you already own or prefer, and reconfigure the layout anytime.
Can I rearrange the strips later if I move the furniture?
Yes. Because there is no solder and no adhesive on the connector itself, you can open the clamp, pull the strip out, and re-lay it in a new configuration without ruining the strip.
Do I need to paint or finish the connectors to match my wall color?
No finishing is required. The boards are intentionally low-profile and sit behind or under the strip itself, so they are not a visible design element once the lights are on.
How do I install these LED strip connectors without soldering?
Cut your LED strip to the marked cut line, peel back a small section of the adhesive backing to expose the copper pads, slide the strip under the pins of the connector or L-shape board with the pads aligned to the four contacts, and press the snap clamp down firmly until it clicks closed. The teeth bite into the copper pads to complete the circuit.
Can these connectors join two strips that were cut on different ends?
Yes, as long as both strips are 10mm wide 4-pin SMD 3528/5050 RGB. The bidirectional RGB+ alignment means the connector works regardless of which side the RGB+ pad lands on, so you do not need to worry about strip orientation when joining the two pieces.
What should I do if my LED strip does not light up after installing the connector?
Open the clamp and check that all four copper pads are fully exposed, clean, and aligned under the pins. Press the clamp down firmly again until it clicks. If the strip still does not light, try the other end of the strip in the connector to rule out a reversed orientation issue, even though the design is bidirectional.
Will this work with Govee, Lepro, TP-Link Tapo, and Monster brand LED strips?
Yes, as long as the strip is 10mm wide with 4 pins and uses SMD 3528 or 5050 RGB chips. The kit is confirmed to work with Govee, Lepro, TP-Link Tapo L900 series, and even offset 3-pin 10mm Monster brand strips when joined with a 4-pin 10mm connector. Verify your strip width and pin count before ordering.
Is this connector compatible with 8mm LED strips or COB / FCOB strips?
This specific kit is for 10mm 4-pin strips only. 8mm strips, FCOB strips, and 2-pin or 3-pin configurations are a different size and require a different connector variant, which is available separately in the same product line.
What is included in the box and what do I need to buy separately?
The kit includes 10 L-shape corner connector boards, 20 straight connector clips, 2 bonus straight couplers, and printed installation instructions, for 32 pieces total. You will need to supply your own 10mm 4-pin RGB LED strip and a compatible 12V power supply, neither of which is included.
Are these connectors safe and reliable for long-term use?
Yes. The connectors are made from standard PCB material with tin-plated contact pins and plastic snap clamps. They are passive components that draw no extra current, run cool under normal 12V LED loads, and are designed for repeated opening and closing without losing grip strength.
Will using a connector dim or discolor my LED strip at the joint?
When the clamp is fully closed on clean copper pads, the electrical contact is solid and there is no perceptible dimming or color shift at the joint. If you notice any dimming, it usually means a pad is not fully seated under the pin, and re-clamping the connector resolves it.
What is the difference between a snap-down solderless connector and a soldered LED strip joint?
A soldered joint uses a hot iron to melt metal onto the copper pads, which creates a strong permanent connection but requires skill, a soldering iron, and a safe workspace. A snap-down connector uses a mechanical clamp to bite into the same copper pads, creating a solid connection in seconds with no heat, no tools, and no permanent modification to the strip.
